Are you wondering how to install a toilet Australia? A certain number of tools are needed to install a toilet, regardless of whether you want to replace your old one or buy a new one. If your toilet is far past its prime, has several plumbing problems, or simply wants to update the aesthetics of your bathroom, you might want to consider replacing it.
You can do the installation of a toilet yourself as a home improvement job. You only need to understand how to install a toilet that the people of Australia would be envious of. This article will go over the steps on how to install a toilet in Bondi area.
How to Know if You Need a Replacement
One of the main causes for needing a replacement is that your present toilet has a lot of problems or is old. You must understand when a replacement toilet is necessary if you want to learn how to install a toilet Australia.
- Suffers from Cracks and Leaks
When a toilet starts to leak or develop cracks, that may also be a sign that it needs to be replaced. A damaged or leaking toilet can result in wet floors and continuous water flow. Fortunately, if it's a recent toilet, it can be fixed. Since toilets typically last 25 years, as was already noted, older toilets are more likely to experience problems.
- If Your Toilet Always Clogs
Regardless of whether your toilet clogs occasionally or consistently, you should investigate the issue. If the issue isn't related to the substance you flush, there can be a problem with the drain pipes. Additionally, if your toilet is an older type, there may be a buildup of mineral deposits. You can call the your local plumber from Bondi to diagnose the cause of the concern and how to fix it.
What Supplies Are Required?
Required Pieces
- Hacksaw
- Teflon Tape
- Putty knife
- Tubing cutter
- Screwdriver set
- Adjustable wrench
Required Materials
- Toilet seat
- Flange
- Tubing supply
- Wax ring
- Specialized bolts
5 Steps on How To Install a Toilet Australia
Make sure you have all the necessary equipment and supplies before you begin. Another thing to keep in mind is to make sure your restroom is clean and ready before you begin. So, here’s how to install a toilet Australia.
1. Turn Off the Main Water Supply, and Remove the Toilet
Make sure to empty your toilet tank and turn off the water system in your bathroom before you begin. Finding and turning the stop valve will first turn off the water supply. Once you've done that, flush the toilet multiple times while hanging on to the handle to empty the tank. Your tank should start to drain itself when you finish this. However, if your tank still contains water, you can empty it using a mop and a sponge.
Start removing your old toilet after turning off the water. Use a pair of pliers first to remove the nuts and bolts from your toilet tank. You may always employ a hacksaw or penetrating oil if the bolts on your toilet appear difficult to loosen. Make sure not to apply too much pressure when removing the bolts with a hacksaw.
Once the toilet tank bolts have been removed, gently detach the water inlet line from the toilet cistern's bottom. After that, take out the toilet's bolts and throw away your cistern. Utilizing your pliers or a socket wrench, remove the toilet bowl next.
2. Get Rid of the Wax Rings
Wear gloves and prepare a throwaway bag to store the wax rings in before you begin because it can be difficult and sticky to detach them. Use a putty knife to scrape the wax ring off, then place the leftover pieces in a trash bag. Additionally, before removing the wax ring, block the drain with a small cloth or rag to lessen the nasty sewer odors.
3. Start Putting the Bolts, Nuts, and Wax Ring
Install the new nuts, wax rings, and bolts after removing the old ones. Turn the bolts 1/4 to the right to tighten them and make sure they are secure. To tighten the nuts, repeat the procedure. The replacement wax ring should then be attached to the toilet's flange part.
4. Secure the Toilet and Position the Valve And Tank
In order for your toilet to correctly align with the bolts and nuts, carefully position it into place by pressing down. Insert washers and nuts into the screws to secure your toilet. Bolts that are exposed should be cut off with a hacksaw before being capped. After that, install the tank, tighten the spud nut, and cover everything with a washer.
By moving it to the inside of your tank, adjust your toilet valve. Then, using your hands, tighten the locknut on your valve. However, you can also use a wrench to compress the locknut a little bit more. Place your tank over the bowl, add two washers to each bolt, and then cover them with a wingnut to seal it in place.
5. Connect the Water Supply Again and Secure it.
By re-connecting the tubing supply to the fill valve, you can restore the water supply. Once the water is flowing again, look for any evidence of leaks or puddles. Try flushing it to make sure everything is operating as it should.
Test your toilet for a few days before sealing it to make sure everything works as it should. After a few days, you can begin caulking it and attaching a toilet seat to it. And that is how to install a toilet Australia.
When to Speak with the Professional Plumber
It's important to know how to install a toilet and do sewer relining Sydney, whether you do it yourself or hire a professional plumbing services in Bondi. Make sure you have all the equipment required to do so. So, if you need assistance and affordable pipes, contact Civic Plumbing. Call them at any time for a cost-free estimate!
